There are several methods that are used for upper cabinet installation. I have thirty years of experience in installing kitchen cupboards. These techniques have proved to be the easiest way for me to hang uppers on the walls. These tips on Cabinet Installation Orem UT will save you hours of frustration if you use them.
Handling Power Tools- The most likely power tool that you'll be handling most of the time is the electric drill and occasionally an electric wood planer for minor adjustments. Whether the drill is portable or not, equipped with wires or with batteries, know that the impact of an electric drill could pose significant damage to your body.
Determine where the bottom of the wall drawers will be located off of the floor and make two adjustable prop sticks out of four pieces of pine. The standard height for installing wall drawers is fifty-four inches off of the floor. These props should be adjusted just a little higher than where the bottom of the drawer will be.
In many cases there are other peripheral details such as electrical wiring and plumbing that have to be looked into and handled simultaneously. The project coordinator from the fixing company will ensure that the entire project is carried-out to perfection.
Watch for the electric line. While drilling any wall, always ensure that you are not drilling in a location where the power lines are situated. This is a newbie mistake that's very dangerous as you can accidentally drill on electric wires inside the wall that you cannot see. Finally, always wear goggles to ensure that dust won't fly in your eyes. The electric drill was invented by Arthur James Arnot and William Blanch Brain in 1889?
Bore three-sixteenths inch wide pores in the back of the initial drawer corresponding in the same locations as where the studs are located on the wall. Place the prop sticks on an angle, slightly below the level line. Hoist the first top drawer up to the level line and move the props so that they support the weight of the cupboard. Hold the drawer steady and secure it to the wall with number two screws.
Move the props over to support the next wall cupboard to be installed. Drill the drawer back in the locations where the screws will sink into the wall studs. Hold the upper in place, adjust the props to hold it up and then use clamps to align the cupboard face with the first wall drawer you installed. Secure the clamps very tightly. Fasten the drawers together in the front first, and then secure the drawer to the wall.
During drawer installation, it would be wise to have a partner or an assistant to offer you help when lifting the drawer to its mounting point; this has two rationales - the first one being the added lifting capacity and the second one for feedback to see if the drawer is level.
Handling Power Tools- The most likely power tool that you'll be handling most of the time is the electric drill and occasionally an electric wood planer for minor adjustments. Whether the drill is portable or not, equipped with wires or with batteries, know that the impact of an electric drill could pose significant damage to your body.
Determine where the bottom of the wall drawers will be located off of the floor and make two adjustable prop sticks out of four pieces of pine. The standard height for installing wall drawers is fifty-four inches off of the floor. These props should be adjusted just a little higher than where the bottom of the drawer will be.
In many cases there are other peripheral details such as electrical wiring and plumbing that have to be looked into and handled simultaneously. The project coordinator from the fixing company will ensure that the entire project is carried-out to perfection.
Watch for the electric line. While drilling any wall, always ensure that you are not drilling in a location where the power lines are situated. This is a newbie mistake that's very dangerous as you can accidentally drill on electric wires inside the wall that you cannot see. Finally, always wear goggles to ensure that dust won't fly in your eyes. The electric drill was invented by Arthur James Arnot and William Blanch Brain in 1889?
Bore three-sixteenths inch wide pores in the back of the initial drawer corresponding in the same locations as where the studs are located on the wall. Place the prop sticks on an angle, slightly below the level line. Hoist the first top drawer up to the level line and move the props so that they support the weight of the cupboard. Hold the drawer steady and secure it to the wall with number two screws.
Move the props over to support the next wall cupboard to be installed. Drill the drawer back in the locations where the screws will sink into the wall studs. Hold the upper in place, adjust the props to hold it up and then use clamps to align the cupboard face with the first wall drawer you installed. Secure the clamps very tightly. Fasten the drawers together in the front first, and then secure the drawer to the wall.
During drawer installation, it would be wise to have a partner or an assistant to offer you help when lifting the drawer to its mounting point; this has two rationales - the first one being the added lifting capacity and the second one for feedback to see if the drawer is level.
About the Author:
If you are looking for the facts about cabinet installation Orem UT residents should come to our web pages today. More details are available at http://www.daltonscabinets.com/products now.
ليست هناك تعليقات:
إرسال تعليق